PG-200 & PG-300
![](https://mppgroup.ir/wp-content/uploads/2023/05/PG-200.jpg)
The UG product s are mechanical-hydraulic governors for controlling diesel, gas, or dual fuel engines, or steam turbines. The governor provides extremely reliable speed control throughout the drive speed and temperature range. This proven design has been the industry standard for many years and its worldwide acceptance provides easy service in most engine and governor […]
EGB-10P/13P/35P/29P/58P/200P/300P
![](https://mppgroup.ir/wp-content/uploads/2023/05/eg3p.jpg)
These EGB governor/actuators are used with Woodward analog or digital electronic controls that provide a proportional 20–160 mA signal to control dual fuel, diesel, and gasoline engines, and gas and steam turbines driving electrical or mechanical loads. EGB-10P /13P /35P Work capacity: 10, 13, 35 ft-lb (14, 18, 48 J) EGB-29P and EGB-58P Work capacity: 29 and 58 ft-lb (39 and […]
3161 Governors
![](https://mppgroup.ir/wp-content/uploads/2023/05/3161-Governor.jpg)
The 3161 governor is a mechanical-hydraulic device that senses speed to control dual fuel engines, diesel engines, or steam turbines. The variety of standard features and available options make the governor ideal for a wide variety of applications that require work capacity of up to 24 N-m (18 lb-ft). Applications include off-highway vehicles, industrial, marine, […]
UG 40 Governors
![](https://mppgroup.ir/wp-content/uploads/2023/05/UG-40-Governors.jpg)
UG-40 governors are used for speed or load control of dual-fuel, diesel, or gas engines or steam turbines with governor drive speeds of 350 to 1050 rpm or 550 to 1300 rpm. They are typically used to drive alternators, DC generators, pumps, compressors, or marine propellers.Governors with lever speed setting are primarily used for propulsion […]
UG MAS Governors
![](https://mppgroup.ir/wp-content/uploads/2023/05/UG-MAS-Governors.jpg)
The UG MAS speed setting system allows remote speed setting using a 4–20 mA current loop. This remote control of engine speed is especially useful in marine applications using milliamp signals instead of the more traditional pneumatic pressure signal.The system consists of a UG-8 Dial governor with a special cover and a separate final driver. […]
UG 8 PL Governors
![](https://mppgroup.ir/wp-content/uploads/2023/05/UG-8PL.jpg)
Woodward’s UG-8PL is a compensated, isochronous governor for use with diesel, gas, and dual-fuel engines or steam and industrial gas turbines driving pumps, compressors, alternators, generators, etc. The UG-8PL governor has an integral oil reservoir (sump) and oil pump and does not require an external oil supply for its operation. The governor also has both […]
UG 8 Governors
![](https://mppgroup.ir/wp-content/uploads/2023/05/UG-8-Governors.jpg)
The UG product s are mechanical-hydraulic governors for controlling diesel, gas, or dual fuel engines, or steam turbines. The governor provides extremely reliable speed control throughout the drive speed and temperature range. This proven design has been the industry standard for many years and its worldwide acceptance provides easy service in most engine and governor […]
UG-25+Governors
![](https://mppgroup.ir/wp-content/uploads/2023/05/ug.jpg)
The GTC190control system is a new generation of turbine control that provides the power of PC technology in a rugged and deterministic system. The flexible and powerful software tools and exceptional computational power make the GTC190 control an ideal solution for controlling a single-shaft large industrial gas turbine. Typical large industrial gas turbine control loops […]
SG Governors
![](https://mppgroup.ir/wp-content/uploads/2023/05/SG-Governors-1.jpg)
Available in work ratings of 10.8 and 21.7 inch-pounds, the SG hydraulic speed-droop type governor is designed for use on small diesel, gas, or gasoline engines where isochronous control is not required. The droop control is such that the governor operates at a slower speed as engine load increases.
PSG Governors
![](https://mppgroup.ir/wp-content/uploads/2023/05/SG-Governors.jpg)
Available in work ratings of 10.8 and 21.7 inch-pounds, the PSG governor is a pressure-compensated, speed-droop, or isochronous governor for controlling the speed of small diesel, gas, and gasoline engines, or small steam or industrial gas turbines. The governor is used to control engines or turbines driving alternators, DC generators, pumps, or compressors.